Zoeken in deze blog

Totaal aantal pageviews

maandag 5 mei 2008

José Ramirez III clase 1 A 1980 and 1981 / Jose Ramirez II 1945 / Jose Roca produced guitar with an Audex label.





This 1980 clase 1A model was built by Enrique
Borreguero who's father was a very fine luthier
as well. Very good condition though the fretwork
was worn out. When placing new frets, the
fingerboard will be flattened out keeping in mind that
the upper bass side allways has some give to let the
lower string vibrate freely. Apart from that the
action at the bridge can be corrected for optimal
playability and small damages to the fingerboard
itself can be cured.
 

Both sides and back are remarkably straight grained.
Maybe not that attractive but it helps for optimal
stability of the wood regarding cracks in the future.
This guitars; own frequency lies on he note A so
in Hz that would be 110 Herz.
 

This label states that between this example and the following
guitar 400 guitars clase 1A have been constructed at the
Ramirez shop. It was booming business in those days.
Apart from the superb sound, most striking detail in comparison
with most other José Ramirez clase 1A guitars is that the sides
in the soundbox are not strenghtened with a layer of cypress
as was common or even partly covered with a rosewood
layer as can be seen on the Camara models. No, this
guitar has been entirely covered with a rosewood layer from
the inside of its' soundbox. So no solid sides but instead
of cypress, rosewood has been used. This message puzzled
Amalia Ramirez as well though she thinks it to be another
experiment executed by her father José Ramirez III.



José Ramirez III clase 1 A (1981)








This eighties Ramirez guitar has been obtained quite
recently. Though it suffered from some humidity damage
its sound was wonderful. Huge volume and the tonal
qualities are exceptional. Beautiful rounded tone for
all frequency registers. You should listen to the Ramirez
guitar on one of the Andres Segovia Youtube movies:
Andres Segovia demonstrates different timbres of the
guitar. The same sounds!



Though the humidity has caused a crack behind the bridge
that was deformed I had to make a device in order to bent
the sides of the crack back. There was enough wood so
after the operation it could easily be glued together.
To my surprise it had a significant effect on the overall
tone production: Even better! Moreover the action was 
way too high. That has been solved by shaving away the
fingerboard towards the head in order to create another
angle neck / body. A refret job was necessary of course.




For those who are keen on labels: the blue rounded Ramirez 
label is a sign of quality and the eighties Ramirez guitars 
are known for their sweet voice. This one has been made 
by Juan Garcia Ray though it bears the number 6 which
stands for Arturo Sanzano. I recently visited the Ramirez
workshop in Madrid where they looked it up for me.
Juan Garcia is no longer member of the workstaff.
There is a site where they give you an explanation of all 
initials they used up until 1991. Amalia Ramirez states
 that their best instruments aren't allways built by the best 
craftsmen as the combination of woods, circumstances 
while built and tension between the different parts also 
attribute to the final sound result.



Jose Ramirez II guitar (1945)





Presented here is a Jose Ramirez II guitar from 1945.
It is well known there was a shortage of about everything 
just after World War II and the Civil War that ended in 1939.
This example has a spruce top with a seven fan bracing.
Ebonized fingerboard with copper fretwork. Brasilian
rosewood bridge with the well known ornamentation
from that period. Some odd things can be found on
this guitar as it has the bigger Blue / white label normally
found on the higher end student models. But the label
has been signed in blue ink (probably the maker) and
most likely afterwards with "J. Ramirez" done by (???)
Scale length: 650 mm - Length of the body: 477 mm -
Neck width: 50 mm (at top nut) Upper Bout: 255 mm
Waist: 218 mm - Lower bout: 342 mm - Depth: 
Varying from 80 to 90 mm (Bottom)


It is obvious that the soundbox has been built with
Cypress but this guitar lacks the golpeadores found on
a real flamenco guitar. Also the bridge height itself is
that of a classical guitar. This instrument produces a
somewhat dry but sweet and "complete'  sound. Very 
even in all registers. In the book "The Ramirez Collection"
written by Brian Whitehouse there is a sound example
included of a 1946 guitar built by Jose Ramirez III.
This guitar is slightly bigger but has the 50 mm nut
width and a seven fan soundboard strutting as well.
The 1946 guitar has been built with better materials
as on most Ramirez guitars of this time a fairly wide
grained soundboard can be found.


Some people will say: Mahogany veneered but close
inspection learns otherwise: This wood is too fine
grained. The typical head form also found on his
concert models is there and the use of metal rollers
can be a later addition as are the tuners as a whole.
Probably this guitar was fitted with tuning pegs
regarding its' weight. a cedar neck that has been 
executed very good. 


In order to make this instrument playable again I had
to shave the fingerboard a bit towards the head. By
that time it became obvious that the fingerboard had
been ebonized in the past. I matched the color close
to the veneering of the head and placed new frets.
As the original top nut was broken I changed it
with an ivory one and I had to lower it a bit as at
that point the fingerboard had been lowered by
about 2 mm. As the frets are a bit higher now this
guitar plays much better though the width at the
nut could have been a bit more spaced.


I suspect these tuners to be quite old as well. They
still work well but aren't securely mounted. The same 
thing can be said about the restorations on this guitar. 
And the question remains: "are they original" as the
thickness of the head varies. So I think this guitar
originally was provided with pegs. These tuners
gave too much problems so I decided to change them 
as well. Schaller tuners have been added now but
being too long for this guitar another extra move
was necessary: The Lyre had to be removed.




These tuners work very well and the original drilled
holes in the head could be reused again. A must!


A simple but gracefully executed rosette. Jose Ramirez II
however will not be remembered as a Rosette maker. 
Some of his guitars even had Rosettes made out of simple 
concentric circles. We have to remember there was a 
shortage of all kinds of materials. This kind of inlay can
also be found on Ramirez guitars of the thirties and even
the following rosette from a Domingo Esteso guitar from
1930 has some similarities.


esteso-1930-rosette

As for labels: The site of Guitarrasramirez speaks of
the white / blue label being used in student models only.
However there are several guitars from the thirties and forties
that have the larger blue label but aren't meant to be student 
guitars. It will probably count for the fifties guitars onwards.


A picture of the bigger blue / white label but signed
anyway. In the middle left the name J Ramirez can
be found but this can be a later addition. The fact that
the signature has been placed partly over the label and the 
wood surrounding it confirms this instrument to be a
genuine Jose Ramirez II. James Greenberg from 
Zavaletas guitars who holds an incredibly inventory
of older classical guitars confirms this big signature
to be from Jose Ramirez III. Hopefully Amalia
Ramirez will confirm it as well in the near future.


Around 1945 there weren't that many luthiers at work
in the Ramirez workshop so maybe we can solve the
mystery about who placed it. The top of this guitar
has been mounted with individual blocks and the 7 fans
are quite small in width (4 mm) and height (3 mm).
Also the seam between the two halves of the back have
been glued together with blocks. Besides the label
this guitar has two stamps: Both near the heel block on
the soundboard and back. Most likely a sign that it has 
been built in Madrid and not in Valencia though the
neck to body construction looks quite Valencia!


Amalia Ramirez states that her father sometimes 
signed the older guitars and then stopped for a while. 
After seeing this picture she states that the signature
does not belong to her father (Jose Ramirez III) but
possibly to her grandfather.


As I already explained this is a Valencian type of neck to
body joint. But it is known that Barbero also constructed
the heels this way. The inner heel however looks entirely 
hardwood to me and the form resembles a lot the thirties 
Santos Hernandez heels.


A comment on the bridge has to be made here as the
form as well as the inlays and the mother of pearl covering 
of the stringblock is pointing towards Ricardo Sanchis 
Nacher. These kind of bridges have been seen on other 
Jose Ramirez II guitars of the forties.



Audex Labelled Guitar (Jose Roca - Valencia)



  

This Valencian made guitar before and after the restoring 
process. I will explain what had to be done and though these
student guitars were overlooked in the near past there seems
to be more interest in them nowadays. However the amount
of work (and costs) it requires in fact is not rewarding if
you need to have it done by a luthier. The final sound
always remains a surprise. This example is really above
expectations. Warm, colorful and a great balance though
it misses the brilliance and volume of a good concert
instrument. But for small venues? Not bad at all!

  

Presented here is an early sixties intermediate model from 
the Audex shop. They didn't produce guitars themselves
but had them made elsewhere in Valencia. I have to find 
out where. The soundboard has a 5 fan bracing and the
rosette has been executed more luxury. But even in those 
days (early sixties) the real concert guitars were already
provided with a wider neck. Therefore this guitar must 
be considered as a nice intermediate student instrument.
Width at the topnut is 50 mm and the scale is 650 mm.

  

The guitar is provided with a nice back but strange detail
was that there is no center strip on the inside of the back.
They glued some broad but flat pieces of wood over the 
seam of the two back halves. I filled the hardly detectable 
seam with some wood glue to strengthen parts.

  

Nothing special has been done to the back furthermore but
it is obvious that the polishing compound did his work.
The own frequency of the soundbox lies on a B (which
means around 123 Hz.)


As the lacquer used in those times crystallizes over time, 
I figured it would be better to have all the lacquer removed 
on the string tie block as the tension of the strings are causing
unwanted traces. So the bridge will be lacquered afterwards.
Most entry level Valencian guitars had a black painted bridge.
This one is made out of rosewood.


What often happened was the kind of sloppy way they 
mounted the heel. No big deal as the sides fall into the gap 
made for a sturdy fit but in fact it simply shouldn't be there. 
The Valencia way of constructing the heel partly with a
softer wood such as spruce hasn't been done here. On
the higher grade models the whole outer heel was 
executed out of hard wood.


The same thing on the other side. I will try to 
place and glue a small splinter of wood in the gap.

   

The tuners need to be cleaned and while doing so 
I will correct the sleeves for the strings fit a bit. The 
topnut is way too high and the plastic it has been made
out of, has been detoriated. A new topnut is a must 
here. The headform is exactly the same on the Roca 
guitars I found on the internet. The site of jedistar is 
a very useful tool regarding information around the 
various luthiers.

A remark can made made around the metal rollers used 
here on the tuners as that is pointing towards a  somewhat 
earlier model, probably made around 1960.

  

Topnut and frets are gone. I removed the copper
(too square!) frets and thus I'm able to correct the 
neck / body angle though it wasn't that bad. Small
traces of nail use in the lowest positions can be 
removed now as well. On the right the guitar
neck as it is now.

 

The Audex label was even provided with a stamp: 
"Made in Spain". But furthermore no type number has 
been mentioned. But seeing the elaborate rosette it 
falls into a higher category.

 


  
The tuners do not look that spectacular but they are
clinched to the base plate and moreover they work securely
with no play on them even after such a long time.
Once cleaned they already look much better!

 

The topnut didn't even fit well and among other
irregularities, this must have been the reason the 
Japanese factories took over this business.

 

An extra half 19th fret will be mounted for the demanding 
pieces and I will clean the rosette but I will leave the sound-
board the way it is. The old lady may show some traces...
Oiling the fingerboard is a must of course, in fact before
the new frets are mounted. The lacquer on these sixties
Spanish guitar solves a bit in pure alcohol which in
fact gives a much better appearance. A polishing process
afterwards is a must. I use "Nicko" very fine polishing
liquid for the last process.


I found this guitar on Jedistar, a great site for finding 
information around guitar factories and luthiers in
electric as well as the acoustic field. They are showing
a "Roca" labelled guitar with exactly the same rosette
on the guitar here above.


Presented here is the "Roca" labelled guitar with exactly
the same rosette and not only that, the bridge and the 
headform also appear to be identical. So this problem 
is solved around the origin of the Audex labelled guitar.
As for the age, this label was used by the Roca plant 
between 1959 - 1964. That also explains the use of 
metal rollers for the tuners used on the Audi guitar.


The Roca labelled guitar is presented here. On the site of 
Jedistar a high end Roca guitar is presented as well, above the
guitar that is showed here. They made guitars "for everyone".
That was their philosophy. Some more information....

José Roca Navarro started his business ROCA
from the remains of Marinnieta. Marinnieta used 
to be the business of María Dolores Marín Soucase 
(granddaughter of the great guitar builder Andrés 
Marín). José Roca was married to Dolores from 
1945 till 1957.

When José took up the guitar production in 1959 
the market for guitars was picking up to skyrocket 
in  the 60’s. José quickly expanded the production 
with electrical guitars and amplifiers. Besides that he 
started to adapt the guitar materials and production 
methods to lower his production costs to achieve 
lower selling prices. It looks like ROCA is one of
the factors for the race to the bottom of Valencian 
guitar productions. In his interview, José states 
that everyone should be in reach of his guitars.

The range of his instruments was big (everyone 
could find a guitar of his choice) it included bandurrias,
 laúds and concert type of guitars as well. The annual 
volume boosted from 3.600 pcs in 1959 till 25.000 in 
1965, with the main destination Valencia and Spain.
Production locations were in Turís and Xirivella. 
Valencia-city housed the shop, some despatch and 
the office. Wether José did business with Mijubal 
in Turís is not known.

With many thanks to Ton Bogaard who already
did a lot of investigations and is always willing
to help. Just visit: guitarrasvalencia.wordpress.
And Inge and Jan of course who also supplied
some extra information. Inge cherished this guitar
but growing older she is not able to play the guitar
anymore. I've showed them the restoration results! 
Some lacquer work, adjusting some sloppy wood-
work, cleaning the tuners and last but not least new 
frets instead of the too square and roughly filed 
original copper fretwork. As the fingerboard wood 
was not that dense I had to glue in these new frets.

And just recently I stumbled onto another brand that
in fact is closely related to the Jose Roca brand: The 
Francisco Bros (and later only "Bros") labelled guitars
learned their craft in the factory of Jose Roca and
Maria Dolores Marin.

(S.Sgroi) Silvestri guitars / Vicente Sanchis / Suzuki / Takeharu GT 500 / Hiroshi Tamura P50



In fact the first Silvestri I've came across. As you can't
hold everything you get your hands on, it has been sold
and in fact I was completely forgotten it!


In fact a very odd model with those two small holes in 
the soundboard on either side of the big soundhole.


The rosewood sides in the lower bout makes it
special as well. It has been supported with a tail-
piece so this was in fact suited for metal strings.


A black painted neck and head but probably still
reinforced with a central placed rosewood inlay.


Another feature that allways is there: The black
cloth piece for dampening the strings.


I haven't been able to find a label but I think this model
to be quite a bit older than the model here beyond. So
my guess is it could be an Ermelinda Silvestri guitar.


This model is presented here in its' unrestored condition.
As the bridge hasn't been properly reglued the soundboard
can be relaquered as well. The kind of lacquer used here
"cristallizes"  over the years and can be easily removed.


The inlay around the soundhole and along the edges
is all made of wood so no stickers and the fingerboard
has been cleaned allready here as are the frets.


As the frets are showing some file traces a 
leveling job in fact was necessary as well.


The so called "zero"  fret I left untreated. The neck could 
have been relacquered as well as this kind of varnish used 
tend to colour the neck in an ugly way but I just left it there.


This label has been used by Ermelinda Silvestri as well.
I don't know about the small label underneath it where
Silvestri states it to be built in the Spanish way. What has
been ment by that remains a mistery as the so called Spanish 
fan bracing simply isn't there: There are two transverse bars
between the bridge and the soundhole and a kind of a 
wooden bridgeplate underneath the bridge.


The bare wood that has been cleaned allready as is
the rosette here. Securely flattening out the bridge
area is a must for a tight fit for the bridge on the 
soundboard. The soundboard is solid spruce. Back 
and sides are made out of mahogany. A rosewood
bridge and fingerboard have been mounted on
this guitar that has a 645 mm scale.




Vicente Sanchis Model 34






A nixce and well built "intermediate" guitar that also
can be found on the "reverb" site. The condition of
this guitar is very nice and it is immediately playable.


Model 34 and year of production 1986. It is known that
also built for several other luthiers and music shops.


The only "minor" on this one: A chip of the heel covering
disappeared. These small repairs can in fact easily been done
by a player by simply putting a heating iron on the wood that
covers the heel. Then it can be removed quite easily and after-
wards making a new one to glue in place.




An ivory bridge saddle also completes this one.


Simple but well working tuners.


A nice rosette completes this guitar.


Suzuki 3067




To be honest I was a bit disappointed after purchasing the
first Suzuki guitar as I heard some promising comments
on these Japanese guitars from the 70 / 80. The first 
example wasn't fitted with a solid top. This one is and
I must say: Much, much better. Finely crafted, it will 
serve the advanced player who is not willing to spent
hundreds of Euro's.


The back that is in a remarkable good condition.


The label that attests the model number and the so well
lay out used for the sought after Suzuki's.


As a little more elaborate model the bridge has been
upgraded with a fancy string tie block.


Straight neck and easy playabilty.



The top wood can be studied here!


Good fretwork!


Some inevitable playing damage to the fretboard.


The Ramirez style headstock.










Takeharu GT 500




These Takeharu guitar has been built with the 
utmost care and a lot of information can be found 
on the internet regarding this brand. Still affordable 
but for how long?? Cedar topped and sides and back
are made out of Brazillian rosewood (veneered)



 A picture of the stunning back. Also the ebony reinforcement
can be seen on this picture. Beautiful straight neck!


The head that hasn't got any flaws.


The label that has been signed by star classical guitar
player Yamamoto. The Kiso Suzuki company built
this beautiful instrument. Just take a look at Harmony
Central User reviews to see what owners have to
say and think about their Suzuki or Takeharu.


The sides that beautifully match the back.




Hiroshi Tamura P50




Guitars that were produced in the seventies and eighties.
These instruments are not that widely known as e.g. the
Masaru Kohno or the Juan Orozco guitars but they are
in fact soundwise no less. Very well built with even a 
lot of similarities to the afore mentioned luthiers.
Ebony fingerboard and a 655 mm scale has been used 
for this guitar that posesses a remarkable sound 
reminiscent of a real concert instrument. Regarding
the veneered sides: Let us not forget that Jose Ramirez
even veneered his concert 1A model on sides and 
back. He experimented a while by using solid
rosewood on a few of these models. I was able
to compare the two different models. The solid 
rosewood example had a slightly darker sound
but differences were very small.....


Veneered back and sides that appear to be Brasilian 
rosewood to me but a very narrow grained solid
soundboard that has been strutted very traditional:
A seven fan placed pattern with two closing struts.
The top has been glued to the sides with blocks
the way the Spanish luthiers tend to work.


This guitar  hasn't been taken care for in a proper way
by looking at the damages on the right. These cosmetic
flaws will be treated in the near future as this 1972 guitar
further survived time in a remarkable way.


A gracefully designed headstock and the odd thing here
is that the standard distance between the axes of the
tuners, 35 mm, is not present here. The former owner
had to make a move to some very cheap and poor
working individual tuners when the original tuners
were not in a working order anymore. Strange thing
is also that a rather cheap plastic topnut was mounted
as well on this guitar. I've changed it into an ivory
one of course with a proper spacing. The tuners will
be changed as well to good working ones.


A simple but satisfying solution was to place pieces
of messing between these tuners that were sawed at
first to be able to mount them properly. Now tuning
is on parr with the standards of this guitar.



Some marks can be determined here as well in the
soundboard but on a rather  cheap guitar as the "lower"
P50,  the choice for a Brasilian wood bridge is quite odd. 
A new bridgebone has been placed as well. Inner gluework 
is very neat but no inner heel has been provided with this 
instrument and in that way you could compare it with the
Juan Orozco model 8 guitar though the Tamura has more 
qualities regarding sound. Just check the Blog I made 
about the Juan Orozco guitars regarding Japanese guitar 
models and their way of pricing them. A model P 50 from 
1972 could be easily compared with a model P 100 from 1978.

From a Japanese source I found out that the two Tamura 
brothers did have a disciple: Mitsuru Tamura is one of the 
founder of Asturias guitars, he is an interesting character, 
a national athlete on clay shooting and a noted golfer and 
bowler as well as a great player.